- 您现在的位置：买卖IC网 > Sheet目录352 > POE33U-1AT (PHIHONG USA)ADAPTER POE INJECTOR 33.6W 56V
Safety Procedures – General Precautions
General - Please read the following precautions
carefully before installing and connecting the
system to a power source.
Note – Only qualified and trained service personnel
(in accordance with IEC 60950 and AS/NZS 3260)
should install, replace, or service the equipment.
Install the system in accordance with Country,
National or to the U.S. National Electric Code if
you are in the United States.
WWW.PHIHONG.COM
4. The POE33U power injector enclosure has
3 threaded (? NPT) openings to
accommodate waterproof / water tight
conduit and or cable glands. WARNING:
To ensure protection against ingress of
water, the connection(s) of the conduit and
or cable glands are threaded with Teflon
tape all the way through the holes in an
enclosure wall.
Precautions:
1. The building facilities in which the product
will be used must provide Isolation to the
main AC Input connector. This connection
requires a fuse or circuit breaker no larger
than 20A for 120 VAC (U.S.A.) or 16A,
5.
The POE33U power injector AC input
connector (located inside enclosure) is a 3
pin terminal block 9.5mm, rated 20 A, 250
V, with M3.5 Nickel Plated steel screws.
The incoming 3 wire/cable must be
minimum 14AWG and or in accordance
with Country, National Electric Code.
230 VAC (international). The building
facilities must protect the PoE33U Power
injector from over current or short-circuits.
2. The POE33U power injector enclosure is
IP67 tested which provides degrees of
protection against access to hazardous
parts, dust and against ingress of water. To
ensure protection against ingress of water,
torque captive screws (4 places) in an “X”
pattern to > 27 inch pound. –Only qualified
service personal should install, replace or
service this equipment. Before connecting,
visit “www.midspans.com” for the latest up
to date specification and contact
6. The POE33U Power injector consists of
“Data & Power” ports. The ports are
providing TNV-1 outputs. The ports use
RJ-45 data sockets. Do not connect
telephone cables into these ports. Only RJ-
45 data cables with waterproof / water tight
connections may be connected to these
sockets.
7. To prevent the POE33U Power injector
from overheating, do not operate the
product in an area that exceeds the
maximum recommended ambient
temperature of -40 oC to +60 oC.
information.
3. The POE33U power injector enclosure
must be mounted vertically but not
8.
Do not work on the POE33U Power
injector or connect or disconnect cables,
during periods of lightning activity.
orientation limited. The enclosure is
provided with a steel 2mm thick zinc plated
mounting bracket. When mounting utilize
the holes in the mounting bracket plate
(10mm holes) 8 places. The preferred
method of mounting is to a vertical 4 inch
or 6 inch pole using 2”3/8 x 16” U-bolts. If
mounting on a flat surface, to sheetrock or
wood and or others material, use 4 M6
fasteners. Other fasteners may be used, but
hardware must be sized to support 4-5
times the weight of the unit.
9. The AC connector wire combination must
be accessible at all times, as it serves as the
main disconnect device to the product.
10. Before servicing the product, always
disconnect the product from its AC source.
11. Equipment is for Pollution degree 2
Environment.
12. Disposal of this product should abide by all
appropriate National laws and regulations.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
POE36D-1AT
ADAPTER POE INJECTOR 33.6W 56V
POE36U-1AT
ADAPTER POE INJECTOR 33.6W 56V
POE370U-480-24-N
POWER SUPPLY 24PORT GIGABIT
POE45-120
ADAPTER POE SPLITTER 45W 12V
POE480U-8UP
POWER SUPPLY 8PORT 480W
POE576U-16AT-N
POWER SUPPLY 16PORTS SNMP
POE576U-24AFAT-N
POWER SUPPLY 24PORTS SNMP
POE576U-8UP-N
POWER SUPPLY 8PORT SNMP 576W
相关代理商/技术参数
POE33U-1AT-R
功能描述:以太网供电 - PoE 33W 56V 0.59V IEEE802.3af Gigabit
RoHS:否 制造商:Phihong 输入电压（标称）:90 VAC to 264 VAC 输出端数量:1 输出功率额定值:15.4 W 输出电压:48 V 输出电流:0.35 A 随附/必需的交流插头:Required
POE33U-560DO
功能描述:以太网供电 - PoE RoHS:否 制造商:Phihong 输入电压（标称）:90 VAC to 264 VAC 输出端数量:1 输出功率额定值:15.4 W 输出电压:48 V 输出电流:0.35 A 随附/必需的交流插头:Required
POE33U-560DO-R
功能描述:以太网供电 - PoE 16.8W 56Vdc 300mA Dual Port PassivePOE
RoHS:否 制造商:Phihong 输入电压（标称）:90 VAC to 264 VAC 输出端数量:1 输出功率额定值:15.4 W 输出电压:48 V 输出电流:0.35 A 随附/必需的交流插头:Required
POE-35088T
制造商:Unicom 功能描述:8 PORT 10/100 POE SWITCH 2*1000T/SFP GBIC AC
POE36D-1AT
功能描述:ADAPTER POE INJECTOR 33.6W 56V RoHS:是 类别:电源 - 外部/内部（非板载） >> 以太网供电 (PoE) 系列:POE36x 标准包装:1 系列:PSA16U 类型:单端口，Midspan 电源供应器 电源（瓦） - 每个端口:15.4W 端口数:1 输入电压:100 ~ 240 VAC 输出电压:48VDC 电流 - 输出:350mA 安装类型:台式 尺寸/尺寸:5.98" L x 2.56" W x 1.42" H（152.0mm x 65.0mm x 36.0mm） 输入连接器:IEC320-C14 效率:65% 工作温度:0°C ~ 40°C 特点:电源线单独销售 相关产品:817-1654-ND - LOCKING LINE CORD 3 COND UK 2M817-1655-ND - LOCKING LINE CORD 3 COND EU 2M817-1656-ND - LOCKING LINE CORD 3 COND US 6'817-1657-ND - LOCKING LINE CORD 3 COND US 6'993-1040-ND - LINE CORD 3 COND UK993-1039-ND - LINE CORD 3 COND US993-1038-ND - LINE CORD 3 COND EU 其它名称:PSA16U-480-R
POE36D-1AT-R
功能描述:以太网供电 - PoE 33.6W 56V 0.6A input 36-72VDC
RoHS:否 制造商:Phihong 输入电压（标称）:90 VAC to 264 VAC 输出端数量:1 输出功率额定值:15.4 W 输出电压:48 V 输出电流:0.35 A 随附/必需的交流插头:Required
POE36U-1AT
功能描述:ADAPTER POE INJECTOR 33.6W 56V RoHS:是 类别:电源 - 外部/内部（非板载） >> 以太网供电 (PoE) 系列:POE36x 标准包装:1 系列:PSA16U 类型:单端口，Midspan 电源供应器 电源（瓦） - 每个端口:15.4W 端口数:1 输入电压:100 ~ 240 VAC 输出电压:48VDC 电流 - 输出:350mA 安装类型:台式 尺寸/尺寸:5.98" L x 2.56" W x 1.42" H（152.0mm x 65.0mm x 36.0mm） 输入连接器:IEC320-C14 效率:65% 工作温度:0°C ~ 40°C 特点:电源线单独销售 相关产品:817-1654-ND - LOCKING LINE CORD 3 COND UK 2M817-1655-ND - LOCKING LINE CORD 3 COND EU 2M817-1656-ND - LOCKING LINE CORD 3 COND US 6'817-1657-ND - LOCKING LINE CORD 3 COND US 6'993-1040-ND - LINE CORD 3 COND UK993-1039-ND - LINE CORD 3 COND US993-1038-ND - LINE CORD 3 COND EU 其它名称:PSA16U-480-R
POE36U-1AT-R
功能描述:以太网供电 - PoE 33.6W 56V 0.6A 802.3at Compliant
RoHS:否 制造商:Phihong 输入电压（标称）:90 VAC to 264 VAC 输出端数量:1 输出功率额定值:15.4 W 输出电压:48 V 输出电流:0.35 A 随附/必需的交流插头:Required